scratched piston
Moderator: Team
scratched piston
While opening the motor plate with a drill for the head gasket to fit properly,(check picture), I got careless and badly scratched the top of the piston because it was on tdc . My question is, can I run it like that or does it have to be replaced?
Re: scratched piston
It looks superficial to me, I've carb stud imprints and roller needles marks and those pistons were fine.
-
- Guru
- Posts: 2151
- Joined: Fri Apr 07, 2006 8:23 pm
- Location:
Re: scratched piston
You may choose to blend the damaged areas with a cartridge roll. Although not likely in the life of this engine, scribe marks have been known to advance into cracks in some instances. A proper blending will most likely eliminate that possibility.
I hope this helps.
I hope this helps.
Re: scratched piston
Maybe you could just use the edge of a sharp pen knife blade to scrape off the apparent flakes. That way there's no chance of getting sanding grit down the bores.
Felix, qui potuit rerum cognscere causas.
Happy is he who can discover the cause of things.
Happy is he who can discover the cause of things.
Re: scratched piston
I agree with what has been said. I would try to keep any sanding debris out of the bore if possible. For the head gasket, next time you have an issue just trim that rivet off. It is just there to keep the gaskets together. For some marine applications I actually cut them all off and add a head gasket sealer between the layers, so they are not important to the gaskets performance. Just an FYI.
Paul
Paul
"It's a fine line between clever and stupid." David St. Hubbins
Re: scratched piston
This ^^ or use a three-sided scraper like this. I'd use a cutting tool of some sort to avoid crumbs of abrasive getting in the bore or rings and ring lands.
-
- Pro
- Posts: 461
- Joined: Sun Feb 13, 2005 11:27 am
- Location:
Re: scratched piston
Don't do anything except put the head back on, it will be fine. You will do more damage than good trying to smooth it. Don't you know that rough finishes and dimples are the way to power?
-
- Pro
- Posts: 365
- Joined: Wed Nov 07, 2012 6:28 pm
- Location: Tallahassee Florida USofA
Re: scratched piston
I'd be more concerned with that apparent gouge that looks to goes past the water passage bead towards the valley.
Re: scratched piston
This is what I'd do, put the piston at TDC, cover the shortblock in a trash bag, cut a hole for that area and tape if off good, sand, blow it off, wipe it off n run it.
Channel About My diy Projects & Reviews https://www.youtube.com/c/BOOTdiy
I know as much as I can learn and try to keep an open mind to anything!
If I didn't overthink stuff I wouldn't be on speedtalk!
I know as much as I can learn and try to keep an open mind to anything!
If I didn't overthink stuff I wouldn't be on speedtalk!
Re: scratched piston
Definitely polish out all sharp edges smooth it out as good with out taking out materail
-
- Guru
- Posts: 4607
- Joined: Sun Sep 18, 2011 11:31 am
- Location: Heading for a bang up with Andromeda as we all are.
Re: scratched piston
If you wipe a thick bead of wheel Bearing grease around the top circumference of the pistion and a film of it on the Bore walls you can wipe away any grinding or polishing crap very ease!
You can cut a man's tongue from his mouth, but that does not mean he’s a liar, it just shows that you fear the truth he might speak about you!
Re: scratched piston
The scratches have no sharp edges but they concern me, yet I have no time nor funds this year to replace the piston, I wish I knew that I could have cut the rivet off.
If I run it like that can it create heat spots that can eventually melt the piston?. For now it will be run on motor but eventually it will be shot with nitrous.
to allencr267 that opening above the water passage is an oil return passage that on this block was totally obstructed (solid shut) and it had to be opened up and there is no connecting "scratch" between the two. Thank you for noticing it.
Thanks to everyone for your help I really appreciate it.
If I run it like that can it create heat spots that can eventually melt the piston?. For now it will be run on motor but eventually it will be shot with nitrous.
to allencr267 that opening above the water passage is an oil return passage that on this block was totally obstructed (solid shut) and it had to be opened up and there is no connecting "scratch" between the two. Thank you for noticing it.
Thanks to everyone for your help I really appreciate it.
-
- Guru
- Posts: 2802
- Joined: Thu Mar 06, 2014 11:55 pm
- Location:
Re: scratched piston
cover the piston top with grease and hand sand the area thru the grease. the grease will keep the grit contained
-
- Guru
- Posts: 1029
- Joined: Mon Sep 10, 2012 1:55 pm
- Location: Anaheim, CA
Re: scratched piston
Tap any high spots or sharp edges LIGHTLY with a SMALL ball peen hammer to reduce any potential for detonation. Bolt it back together and run it.