Looking For a solid flat tappet cam for 383 sbc
4.030x3.75
5.7 rod
Appoximately 11.1 compression haven't checked yet
Zero deck
Vortec heads, beehive springs plan on using PAC 1218, have not purchased yet
No rockers as of yet, 1.6 or 1.5 or a combination
Edelbrock victor for vortecs
750 dp Holley
1 3/4 headers open exhaust.
Msd 7al 2
3156 w/ driver
5.38 gear
Powerglide with transbrake
5200 stall.
This a bracket only car.
Rpm don't mind turning it 7400-7500, although I'm not sure if heads will support it. Thanks
Cam selection sbc 383 vortec heads
Moderator: Team
Re: Cam selection sbc 383 vortec heads
One of the Crane Saturday Night Special solid lifter cams will get it done
F-256/3634-2S-5 If the cr is 11:1 or less
You can go a little bigger with more generous
compression ratio
F-260/3694-2S-6
Call Crane Cams if you want something different than you see in the catalog
or need a cam on a smaller base circle for chevy rod clearance.
Either are fine with a 1.5 rocker. Crane can advise on the best PAC valve spring.
F-256/3634-2S-5 If the cr is 11:1 or less
You can go a little bigger with more generous
compression ratio
F-260/3694-2S-6
Call Crane Cams if you want something different than you see in the catalog
or need a cam on a smaller base circle for chevy rod clearance.
Either are fine with a 1.5 rocker. Crane can advise on the best PAC valve spring.
Re: Cam selection sbc 383 vortec heads
Those heads are WAY undersized. You need about 35cc more in your intake runner.
Did you mean the large port bowtie vortecs? They would be about perfect with a little porting.
Did you mean the large port bowtie vortecs? They would be about perfect with a little porting.
LOL, according to the post count I'm an "expert." The only thing I'm an expert at is asking questions.
-
- Expert
- Posts: 654
- Joined: Fri Dec 05, 2008 5:24 pm
- Location: san diego
Re: Cam selection sbc 383 vortec heads
If they are 062 or 906 castings , and at least bowl ported ...i would go 248 -262 @ .050 and .540ish lift with a 108 lsa .
Re: Cam selection sbc 383 vortec heads
That is the cam a friend used (trmnatr) and it ran well. I have used some of those lobes due to him liking them so much. They made excellent power for me too.F-BIRD'88 wrote:One of the Crane Saturday Night Special solid lifter cams will get it done
F-256/3634-2S-5 If the cr is 11:1 or less
You can go a little bigger with more generous
compression ratio
F-260/3694-2S-6
Call Crane Cams if you want something different than you see in the catalog
or need a cam on a smaller base circle for chevy rod clearance.
Either are fine with a 1.5 rocker. Crane can advise on the best PAC valve spring.
Re: Cam selection sbc 383 vortec heads
With that stall, I'd recommend my part# M79362A-80362-108
260/263@.050"
.362"/.362" Lobe Lift
108 LSA
I'd also go with a 1.65 or 1.7 rocker on the intake, and a 1.6 rocker on the exhaust.
This would work great with the PAC 1218 spring.
260/263@.050"
.362"/.362" Lobe Lift
108 LSA
I'd also go with a 1.65 or 1.7 rocker on the intake, and a 1.6 rocker on the exhaust.
This would work great with the PAC 1218 spring.
Mike Jones
Jones Cam Designs
Denver, NC
jonescams@bellsouth.net
http://www.jonescams.com
Jones Cam Designs' HotPass Vendors Forum: viewforum.php?f=44
(704)489-2449
Jones Cam Designs
Denver, NC
jonescams@bellsouth.net
http://www.jonescams.com
Jones Cam Designs' HotPass Vendors Forum: viewforum.php?f=44
(704)489-2449
-
- Member
- Posts: 113
- Joined: Wed Mar 07, 2012 10:27 am
- Location:
Re: Cam selection sbc 383 vortec heads
Comp 12-705-8. Its not to big, but not to small. Your heads aren't quite big enough for your combo.
I wound run 1.6 rockers on both and call it a day. The PAC springs are a very good choice.
I wound run 1.6 rockers on both and call it a day. The PAC springs are a very good choice.
Re: Cam selection sbc 383 vortec heads
That part number refers to a roller cam. Might be a little rough on the flat tappet lifters.MidgetMotorsports07 wrote:Comp 12-705-8. Its not to big, but not to small. Your heads aren't quite big enough for your combo.
I wound run 1.6 rockers on both and call it a day. The PAC springs are a very good choice.
Re: Cam selection sbc 383 vortec heads
Thank you for the replies guys. I will look over them and see what i decide.
Morgan Allen