Chevy L6 250" harmonic balancer
Moderator: Team
- BrazilianZ28Camaro
- Guru
- Posts: 3939
- Joined: Mon Feb 09, 2009 10:52 pm
- Location:
Chevy L6 250" harmonic balancer
Hello fellows
I'm helping a friend select the parts to his L6 mild N/A engine...since there are no decent harmonic dampers for it here in Brazil and that engine have harmonic problems by nature, I'm wondering if a SBC harmonic damper can be used with out major milling/mods on the crank ,damper or cam gears cover.
Somebody did this before??
Which would be the ideal damper OD size?
Thanks for replies
I'm helping a friend select the parts to his L6 mild N/A engine...since there are no decent harmonic dampers for it here in Brazil and that engine have harmonic problems by nature, I'm wondering if a SBC harmonic damper can be used with out major milling/mods on the crank ,damper or cam gears cover.
Somebody did this before??
Which would be the ideal damper OD size?
Thanks for replies
'71 Z28 street strip car
Pump gas All motor SBC 427
3308 lbs-29x10.5 Hoosiers
NEW BEST ET
1.38 60' / 4.05 330' / 6.32@111.25mph
https://www.youtube.com/watch?v=99p13UK ... ture=share
Pump gas All motor SBC 427
3308 lbs-29x10.5 Hoosiers
NEW BEST ET
1.38 60' / 4.05 330' / 6.32@111.25mph
https://www.youtube.com/watch?v=99p13UK ... ture=share
- BrazilianZ28Camaro
- Guru
- Posts: 3939
- Joined: Mon Feb 09, 2009 10:52 pm
- Location:
153" L4 ?robert1 wrote:I used a 350 balancer on a L4 with no problems or trouble.
'71 Z28 street strip car
Pump gas All motor SBC 427
3308 lbs-29x10.5 Hoosiers
NEW BEST ET
1.38 60' / 4.05 330' / 6.32@111.25mph
https://www.youtube.com/watch?v=99p13UK ... ture=share
Pump gas All motor SBC 427
3308 lbs-29x10.5 Hoosiers
NEW BEST ET
1.38 60' / 4.05 330' / 6.32@111.25mph
https://www.youtube.com/watch?v=99p13UK ... ture=share
- BrazilianZ28Camaro
- Guru
- Posts: 3939
- Joined: Mon Feb 09, 2009 10:52 pm
- Location:
If memory serves me right , the 151 crank snout and timing cover retainer is the same 250"...robert1 wrote:151", 2.5, Pontiac.
The engine you mean had a previous damper or only a crank hub?
'71 Z28 street strip car
Pump gas All motor SBC 427
3308 lbs-29x10.5 Hoosiers
NEW BEST ET
1.38 60' / 4.05 330' / 6.32@111.25mph
https://www.youtube.com/watch?v=99p13UK ... ture=share
Pump gas All motor SBC 427
3308 lbs-29x10.5 Hoosiers
NEW BEST ET
1.38 60' / 4.05 330' / 6.32@111.25mph
https://www.youtube.com/watch?v=99p13UK ... ture=share
- BrazilianZ28Camaro
- Guru
- Posts: 3939
- Joined: Mon Feb 09, 2009 10:52 pm
- Location:
Thank you Robert for the helpfull info
'71 Z28 street strip car
Pump gas All motor SBC 427
3308 lbs-29x10.5 Hoosiers
NEW BEST ET
1.38 60' / 4.05 330' / 6.32@111.25mph
https://www.youtube.com/watch?v=99p13UK ... ture=share
Pump gas All motor SBC 427
3308 lbs-29x10.5 Hoosiers
NEW BEST ET
1.38 60' / 4.05 330' / 6.32@111.25mph
https://www.youtube.com/watch?v=99p13UK ... ture=share
-
- Member
- Posts: 60
- Joined: Tue Jan 27, 2009 9:58 pm
- Location: newmarker ontario
- BrazilianZ28Camaro
- Guru
- Posts: 3939
- Joined: Mon Feb 09, 2009 10:52 pm
- Location:
thanks for replyspeedymatt wrote:we use a fluidampner on a couple of inline six engines we do. you just have to make/modify a timing pointer as the marks don't line up with the six cylinder pointer
Can you tell a little more about the L6 you build? (power, combo, usage)
Just curious because I never hear/read about a N/A Chevy 250 modified in the US...maybe I need read more
Here in Brazil we have plenty of Chevy 250s on street and drag cars...It was factory installed in Chevy Opala and Chevy Caravan... The fastest drag cars running with it run the 1/4 mile in 11.1s @ 2800lbs N/A and 7.8s @ 2400lbs on single turbocharged Opalas.
Here we have a factory "hot" L6 , called 250-S that was equipped with a mechanical cam and more CR and had 171 factory ponies
'71 Z28 street strip car
Pump gas All motor SBC 427
3308 lbs-29x10.5 Hoosiers
NEW BEST ET
1.38 60' / 4.05 330' / 6.32@111.25mph
https://www.youtube.com/watch?v=99p13UK ... ture=share
Pump gas All motor SBC 427
3308 lbs-29x10.5 Hoosiers
NEW BEST ET
1.38 60' / 4.05 330' / 6.32@111.25mph
https://www.youtube.com/watch?v=99p13UK ... ture=share
-
- Guru
- Posts: 8706
- Joined: Sun Jan 21, 2007 1:16 pm
- Location: Victoria BC Canada
We did one for a guy that we sleeved out to 4"
Used a 11-1 327 LW piston with Crower rods(custom made for the 250 engine)
Used a ported 194 cyl head and a modified 350 balancer to finish the job.
Used a Clifford 4bbl intake and 650 holley in a pu truck.
A tri-y header was all that we could get at the time but made good power did not get any dyno numbers on it but would blow the tires off through 2nd gear with a th350 2200 stall and 308 rear gear
He would turn it to 6800 all day long.
Used a 11-1 327 LW piston with Crower rods(custom made for the 250 engine)
Used a ported 194 cyl head and a modified 350 balancer to finish the job.
Used a Clifford 4bbl intake and 650 holley in a pu truck.
A tri-y header was all that we could get at the time but made good power did not get any dyno numbers on it but would blow the tires off through 2nd gear with a th350 2200 stall and 308 rear gear
He would turn it to 6800 all day long.
Real Race Cars Don't Have Doors
- BrazilianZ28Camaro
- Guru
- Posts: 3939
- Joined: Mon Feb 09, 2009 10:52 pm
- Location:
CoooollllProPower engines wrote:We did one for a guy that we sleeved out to 4"
Used a 11-1 327 LW piston with Crower rods(custom made for the 250 engine)
Used a ported 194 cyl head and a modified 350 balancer to finish the job.
Used a Clifford 4bbl intake and 650 holley in a pu truck.
A tri-y header was all that we could get at the time but made good power did not get any dyno numbers on it but would blow the tires off through 2nd gear with a th350 2200 stall and 308 rear gear
He would turn it to 6800 all day long.
With 194 head you mean 1.94 valves?
You remember what cam that engine had?
Here, some builders overbore the 250 block to 4" with out sleeves...good street L6 have about 330 hp
Thanks for reply
'71 Z28 street strip car
Pump gas All motor SBC 427
3308 lbs-29x10.5 Hoosiers
NEW BEST ET
1.38 60' / 4.05 330' / 6.32@111.25mph
https://www.youtube.com/watch?v=99p13UK ... ture=share
Pump gas All motor SBC 427
3308 lbs-29x10.5 Hoosiers
NEW BEST ET
1.38 60' / 4.05 330' / 6.32@111.25mph
https://www.youtube.com/watch?v=99p13UK ... ture=share
http://en.wikipedia.org/wiki/Chevrolet_ ... gine#194_2
Same head with smaller chamber, gives higher compression on larger engines.
Do you remove the head bolt column from the intake port and use a short stud and nut?
Same head with smaller chamber, gives higher compression on larger engines.
Do you remove the head bolt column from the intake port and use a short stud and nut?
-
- Guru
- Posts: 8706
- Joined: Sun Jan 21, 2007 1:16 pm
- Location: Victoria BC Canada
No a 194 head is from a 194cid block.
It was the first engine of that model run then came a 230 then a 250 ect.
We put 1.94 valves in the head but needed to massage the chamber quite a bit.
The 230 head work out better and with .080 off was about the same size in the end.
Going to 4.00" is getting real thin and especially #1 hole behind the water pump.
if the sonic checked the block I would bet they may had .080 of cyl. wall left and # 1 would be paper thin. What ever floats your boat I guess but would not go out that far with out sleeves in at least #1 and #6. Seen too many crack.
It was the first engine of that model run then came a 230 then a 250 ect.
We put 1.94 valves in the head but needed to massage the chamber quite a bit.
The 230 head work out better and with .080 off was about the same size in the end.
Going to 4.00" is getting real thin and especially #1 hole behind the water pump.
if the sonic checked the block I would bet they may had .080 of cyl. wall left and # 1 would be paper thin. What ever floats your boat I guess but would not go out that far with out sleeves in at least #1 and #6. Seen too many crack.
Real Race Cars Don't Have Doors
-
- Guru
- Posts: 8706
- Joined: Sun Jan 21, 2007 1:16 pm
- Location: Victoria BC Canada
No I used a allen head cap screw and put a 1/2" pipe plug in the top of the bolt hole to seal it.Tuner wrote:
Do you remove the head bolt column from the intake port and use a short stud and nut?
A bit of a pain to get the threads down far enough to get the bottom of the plug flush with the inner port side of the hole.
It probablly did not make any diffefence to flow but seem like the right thing to do.
Real Race Cars Don't Have Doors
- BrazilianZ28Camaro
- Guru
- Posts: 3939
- Joined: Mon Feb 09, 2009 10:52 pm
- Location:
Here we have ethanol L6 with 54cc heads...Tuner wrote:http://en.wikipedia.org/wiki/Chevrolet_ ... gine#194_2
Same head with smaller chamber, gives higher compression on larger engines.
Do you remove the head bolt column from the intake port and use a short stud and nut?
Acually, if you remove the bolt column and put a bolt inside the port, the turbulence generated negates any possible gain. Not a good mod.
Thanks for reply
'71 Z28 street strip car
Pump gas All motor SBC 427
3308 lbs-29x10.5 Hoosiers
NEW BEST ET
1.38 60' / 4.05 330' / 6.32@111.25mph
https://www.youtube.com/watch?v=99p13UK ... ture=share
Pump gas All motor SBC 427
3308 lbs-29x10.5 Hoosiers
NEW BEST ET
1.38 60' / 4.05 330' / 6.32@111.25mph
https://www.youtube.com/watch?v=99p13UK ... ture=share