Hurrican vs. Victor Jr. vs. GM Intake
Moderator: Team
Hurrican vs. Victor Jr. vs. GM Intake
I am purchasing a setof dart iron eagle platinum 215 heads. My old intake was the professional products intake for vortec heads. I have to buy a new one just wondering is the victor jr. better or is the hurricane ok. Or how about one of GM'S INtake
I have had good luck with both the Hurricane and Super Hurricane intakes after some port work like with any intake
2007 HotRod Drag Week Winner SB/NA
2012 HotRod Drag Week Winner SS SB/NA
Fastest/Quickest Small Block N/A
Stock Suspension Car on Drag Week since 2007
9.67@ 139 with a 1.42 60' thru the Mufflers Dot tires
Thanks RFD Heads and Intakes
2012 HotRod Drag Week Winner SS SB/NA
Fastest/Quickest Small Block N/A
Stock Suspension Car on Drag Week since 2007
9.67@ 139 with a 1.42 60' thru the Mufflers Dot tires
Thanks RFD Heads and Intakes
- jmarkaudio
- Vendor
- Posts: 4222
- Joined: Wed Sep 26, 2007 11:26 am
- Location: Florida
-
- Guru
- Posts: 2011
- Joined: Tue Oct 12, 2004 1:19 pm
- Location: Dillsburg, PA
- Contact:
-
- Guru
- Posts: 1259
- Joined: Fri Jan 25, 2008 6:37 am
- Location: New Zealand
-
- Guru
- Posts: 6046
- Joined: Sat May 20, 2006 6:28 pm
- Location:
-
- Guru
- Posts: 2011
- Joined: Tue Oct 12, 2004 1:19 pm
- Location: Dillsburg, PA
- Contact:
Power in at 7600, rev to 8000. I adjust the elephant ears for runner length. get the radius right on the carb flange to bottom of plenum. Adjust CSA and taper. port match to cylinder head and bolt it on.
no welding, no wild spacers...very easy to work on. Total Job cost $375.00. I have had well over a grand in super-vics pre-bowtie/motown and they don't touch the new stuff.
no welding, no wild spacers...very easy to work on. Total Job cost $375.00. I have had well over a grand in super-vics pre-bowtie/motown and they don't touch the new stuff.
I have had good luck with Dart single plane intakes and Edelbrock Victor E intakes on SB chevy engines using Dart 215 headsairflowdevelop wrote:Power in at 7600, rev to 8000. I adjust the elephant ears for runner length. get the radius right on the carb flange to bottom of plenum. Adjust CSA and taper. port match to cylinder head and bolt it on.
no welding, no wild spacers...very easy to work on. Total Job cost $375.00. I have had well over a grand in super-vics pre-bowtie/motown and they don't touch the new stuff.
I have also used Professional Products and had descent results too on the track
-
- Member
- Posts: 146
- Joined: Wed Aug 22, 2007 1:12 am
- Location: Bement IL
It is designed in USA built in China. Very good line of sight, Tall plenum
2007 HotRod Drag Week Winner SB/NA
2012 HotRod Drag Week Winner SS SB/NA
Fastest/Quickest Small Block N/A
Stock Suspension Car on Drag Week since 2007
9.67@ 139 with a 1.42 60' thru the Mufflers Dot tires
Thanks RFD Heads and Intakes
2012 HotRod Drag Week Winner SS SB/NA
Fastest/Quickest Small Block N/A
Stock Suspension Car on Drag Week since 2007
9.67@ 139 with a 1.42 60' thru the Mufflers Dot tires
Thanks RFD Heads and Intakes