are guys cutting 3 ange to valves & whats the cost

NOT ALLOWED: Selling or reselling in a retail manner.

Moderator: Team

gunt
Member
Member
Posts: 92
Joined: Sun Sep 26, 2010 1:52 pm

are guys cutting 3 ange to valves & whats the cost

Postby gunt » Sun Jul 02, 2017 5:12 pm

Hi

So I dropped of a set of heads and asked for the 3 angle valve job exhaust throats to be opened 1mm and back cut , said no problem he's got the newan bb. any way collected all , went to install the new springs valves stem seals and seats look good but he decided not to open up the exhaust , and only 45deg on the valves , no back cut either . what is the run of the mill pricing for doing the job correctly to finish it and cut all the relevant angles into the valves , say 16v heads or am i wrong and this is not normally cried out , I am aiming to do our own heads here in the future but what is the general cost and or is it really a nonprofit procedure [ pain in the ass ]

Cheers

superpursuit
Member
Member
Posts: 59
Joined: Sun Apr 20, 2014 10:07 pm

Re: are guys cutting 3 ange to valves & whats the cost

Postby superpursuit » Sun Jul 02, 2017 7:29 pm

You should post this in "Engine Tech" not here. It is not really relevant in the "Classifieds". You should get your question answered in the Engine Tech section.

ProPower engines
Guru
Guru
Posts: 6781
Joined: Sun Jan 21, 2007 1:16 pm
Location: VICTORIA BC CANADA

Re: are guys cutting 3 ange to valves & whats the cost

Postby ProPower engines » Sun Jul 02, 2017 11:05 pm

gunt wrote:Hi

So I dropped of a set of heads and asked for the 3 angle valve job exhaust throats to be opened 1mm and back cut , said no problem he's got the newan bb. any way collected all , went to install the new springs valves stem seals and seats look good but he decided not to open up the exhaust , and only 45deg on the valves , no back cut either . what is the run of the mill pricing for doing the job correctly to finish it and cut all the relevant angles into the valves , say 16v heads or am i wrong and this is not normally cried out , I am aiming to do our own heads here in the future but what is the general cost and or is it really a nonprofit procedure [ pain in the ass ]

Cheers



repost in SHOP TECH
There will be many replies this is the wrong area for this stuff
Real Race Cars Don't Have Doors

gunt
Member
Member
Posts: 92
Joined: Sun Sep 26, 2010 1:52 pm

Re: are guys cutting 3 ange to valves & whats the cost

Postby gunt » Mon Jul 03, 2017 4:43 am

SORRY
How do i swop it over

gunt
Member
Member
Posts: 92
Joined: Sun Sep 26, 2010 1:52 pm

Re: are guys cutting 3 ange to valves & whats the cost

Postby gunt » Mon Jul 03, 2017 9:21 am

or if some one could delete it from here

Cheers

ProPower engines
Guru
Guru
Posts: 6781
Joined: Sun Jan 21, 2007 1:16 pm
Location: VICTORIA BC CANADA

Re: are guys cutting 3 ange to valves & whats the cost

Postby ProPower engines » Mon Jul 03, 2017 2:05 pm

gunt wrote:or if some one could delete it from here

Cheers



Just repost you questions in the SHOP TECH forum :D
Real Race Cars Don't Have Doors


Return to “Shop Equipment - For Sale or Wanted”

Who is online

Users browsing this forum: No registered users and 5 guests