FS: Engine parts (LT1/SBC, 18*, etc)

NOT ALLOWED: Selling or reselling in a retail manner.

Moderator: Team

Post Reply
User avatar
AdioSS
Member
Member
Posts: 196
Joined: Sat Aug 12, 2006 2:38 am
Location: Kilgore, TX
Contact:

FS: Engine parts (LT1/SBC, 18*, etc)

Post by AdioSS » Fri Jul 09, 2010 8:31 pm

When I was going to the School of Automotive Machinists, I started working on a plan for an engine for my 96 Impala SS. The original plan was to build an LT1 stroker with 18* top end and hydraulic roller valvetrain. Parts were bought over time that would specifically work with the small 4” bore. However, I haven't done anything with it for a long, long time, and I just got a divorce. Not having her income every month hasn’t been easy, and to make things worse, dating isn’t inexpensive. So, now I need to get rid of this stuff.

All prices are negotiable plus shipping.
Reply to the thread or email Chestonphillips@yahoo.com if you are interested, have questions, etc.

$1750 for all 18* Top-End Stuff.
$2000 for 18* top end stuff + pistons.
$850 GM 18* heads. As cast ports and chambers. No valveguides or seats installed ever.
$300 Jesel 1.7i/1.8e shaft rockers, offset for these heads, but no stands.
$250 Titanium 2.080/1.625 valves, with longer stems also for these heads.
$350 Bottom half of sheetmetal intake for 18* heads. Has bungs for nitrous or alcohol injectors installed in the runners. Needs the top fabricated. Would also need bungs added for EFI Injectors.
$50 Titanium Valvespring Retainers


$350 Wiseco forged pistons for 18* heads. These were custom ordered back in 1995 for the NASCAR SuperTruck series. According to Brian Nutter at Wiseco, “The pistons will handle about any power you want to put to them N/A and would be good for a 250 to 300 shot of nitrous if properly tuned, but I'd say the limitation of the pins is at 700hp or so.. I'd go tool steel past that.”
4.028” bore. 1.125" compression height, -14cc reverse dome. 1/16, 1/16, 3mm rings. 0.92 pin diameter (Rings, locks, & pins not included). Never been run.

$150 CompCams 875-16 Roller Lifters

I will be adding pictures soon.
And more parts to be added later.
Cheston Phillips
96 Impala SS
05 Silverado

User avatar
AdioSS
Member
Member
Posts: 196
Joined: Sat Aug 12, 2006 2:38 am
Location: Kilgore, TX
Contact:

Re: FS: Engine parts (LT1/SBC, 18*, etc)

Post by AdioSS » Thu Jul 15, 2010 4:20 am

Here is a picture of what the tops of the pistons look like:
Image

And a few of the intake:
Image
Image
Image

Cheston

User avatar
AdioSS
Member
Member
Posts: 196
Joined: Sat Aug 12, 2006 2:38 am
Location: Kilgore, TX
Contact:

Re: FS: Engine parts (LT1/SBC, 18*, etc)

Post by AdioSS » Thu Jul 15, 2010 8:50 pm

Adding more stuff and pictures.

$180 Ferrea 5000 Series Stainless Steel Valves
9 of each with 1 of each out of the wrapper for airflow bench testing, but still in perfect condition
F5022 = 2.055” diameter x 11/32 stem x 5.010 length
F5025 = 1.600” diameter x 11/32 stem x 5.010 length
I can post pictures, but everybody has seen brand new shiny valves in Ferrea wrappers and boxes, right?

Jesel slotted shaft rockers: The rockers are 1.7in/1.8ex, 1.650 pivot length, .550/.080 offset, pair on a single shaft.
Image
Image
Ti Valves:
2.080/1.627, 5.503/5.443 long, .342 stem
Image
Image

mnmatt
Pro
Pro
Posts: 219
Joined: Fri Oct 08, 2010 2:50 pm

Re: FS: Engine parts (LT1/SBC, 18*, etc)

Post by mnmatt » Mon Oct 11, 2010 11:40 am

What stroke and rod are the pistons for? And are the heads cast iron or aluminum. Ported, unported?
Matt Hasara
Outkast Racing Engines
Lakefield, Minnesota

Post Reply