someone pick me out a 4l80e lockup converter

Transmission to Rear-end

Moderator: Team

Post Reply
tchapps88
New Member
New Member
Posts: 3
Joined: Thu Dec 10, 2015 2:43 pm

someone pick me out a 4l80e lockup converter

Post by tchapps88 » Fri Dec 29, 2017 5:08 pm

swapped a 1997 4l80e into a 70 chevelle with a tci ez tcu and tps adapter for carb and left the stock converter in it to get it going, deffinatley needs a higher stall than 1400rpms. has a 496 with 500-525 hp, 168 tooth flywheel, 3.31 rear gear, 26" tall tires, 6000-6500rpm redline. Looking for a nice but not expensive converter with lockup with 2500 rpm stahl at most, willing to spend $1,000 max, i see hughes, b&m, cirdle d as some options, hughes are closer to $600 and circle d is $900, any input or other brands that would fit the bill?

A_VAS
Member
Member
Posts: 149
Joined: Thu Dec 03, 2009 1:52 pm
Location: Harrisburg, PA

Re: someone pick me out a 4l80e lockup converter

Post by A_VAS » Tue Jan 02, 2018 10:40 am

I've had good luck with FTI, out of Florida
you can get single disc lockup or triple disc...that will hold big power.

you may want to consider the triple, with your gear and car weight, big block torque...it will load it fairly hard.
they will tailor to whatever stall you want...probably a 2800 is what I would go with.

http://ftiperformance.com/FTI-10-Perfor ... -PMLX4.htm
too lazy to make power w/o boost

Speedbump
Guru
Guru
Posts: 1043
Joined: Thu Nov 22, 2007 10:53 am
Location: AZ

Re: someone pick me out a 4l80e lockup converter

Post by Speedbump » Tue Jan 02, 2018 12:00 pm

Have virtually the same set up as you in a 55 Chevy PU, about same weight. 505 CID, 240ish @ .050 - .600 lift TCI controller, TPS add on maybe 575 HP. Had the 4L80 done by Joel on Joy out of Detroit and used his spec converter/lock up clutch, brand I can't remember. I found the receipt and paid about $950 for the converter. It has 6 bolts instead of three holding it on(may be no consequence, but interesting) and when the clutch engages, it does it with authority. All this to say, IMO, don't scrimp on the converter.
From driving the truck for a while I'll say I wish I had dropped the stall from 3K to about 25-2700 but the number is pretty subjective for each engine and the TCI controller has a ton of flexibility that can make for a sweet ride.
Speedbump
"If it was easy, everybody would do it."

77cruiser
Expert
Expert
Posts: 994
Joined: Fri Dec 29, 2006 10:32 pm
Location: I Falls MN
Contact:

Re: someone pick me out a 4l80e lockup converter

Post by 77cruiser » Tue Jan 02, 2018 7:01 pm

Check with Jake see what he has.

http://www.jakesperformance.com/
Jim

AICLLC
New Member
New Member
Posts: 5
Joined: Thu Jan 04, 2018 1:34 pm

Re: someone pick me out a 4l80e lockup converter

Post by AICLLC » Thu Jan 04, 2018 7:57 pm

I've had great luck with Pro Torque converters. Within a month we went thru 2 Tci and 1 A1 Trans unit. Tci converters broke at the welds. :(

AICLLC
New Member
New Member
Posts: 5
Joined: Thu Jan 04, 2018 1:34 pm

Re: someone pick me out a 4l80e lockup converter

Post by AICLLC » Thu Jan 04, 2018 9:10 pm

I've had great luck with Pro Torque converters. Within a month we went thru 2 Tci and 1 A1 Trans unit. Tci converters broke at the welds. :(

Skeezix
Member
Member
Posts: 94
Joined: Sat Jul 14, 2012 8:34 pm

Re: someone pick me out a 4l80e lockup converter

Post by Skeezix » Fri Jan 05, 2018 3:54 am

Call Chris @ CKPerformance.com. He innovates, others try to follow.

Performance & durability for your specific combo & usage = Chris & CKP

stealth
Guru
Guru
Posts: 1001
Joined: Fri Jun 30, 2006 9:37 am

Re: someone pick me out a 4l80e lockup converter

Post by stealth » Mon Jan 15, 2018 2:06 pm

I always wondered why anyone needed to hammer on converter fully locked. Maybe, but it seems like a nice option just for cruise....unlocked for when at wot.
The reasonable man adapts himself to the world; the unreasonable one persists in trying to adapt the world to himself. Therefore, all progress depends on the unreasonable man.

Post Reply