Page 1 of 7
4.6250 piston in a stock 350 block
Posted: Sat Sep 30, 2017 1:34 pm
by SchmidtMotorWorks
Can you figure out how to put a 4.625 piston in a stock 350 block?
This is a stupid question to waste your time.
Please make 20 pages of posts arguing about it.
Re: 4.6250 piston in a stock 350 block
Posted: Sat Sep 30, 2017 1:44 pm
by ZIGGY
Re: 4.6250 piston in a stock 350 block
Posted: Sat Sep 30, 2017 1:54 pm
by John Wallace
What's the bore spacing on a sbc 350?
Helping the post count.
Re: 4.6250 piston in a stock 350 block
Posted: Sat Sep 30, 2017 1:55 pm
by Amilcar
Shouldn`t that be at "advanced tech"?
Re: 4.6250 piston in a stock 350 block
Posted: Sat Sep 30, 2017 2:16 pm
by blykins
Re: 4.6250 piston in a stock 350 block
Posted: Sat Sep 30, 2017 2:16 pm
by RevTheory
Only if it scales!
Re: 4.6250 piston in a stock 350 block
Posted: Sat Sep 30, 2017 2:20 pm
by Keith Morganstein
No problem, I do that all the time with 1960's, 283 blocks and make over 4,000 HP with no failures.
Re: 4.6250 piston in a stock 350 block
Posted: Sat Sep 30, 2017 2:25 pm
by user-17438
How much bore energy would that give us?
If we take 4.625 and subtract that from 350, then add 7.56113 ( that number makes the formula work because its a 4.625 bore) that will give your the bore energy.
I'm off on vacation tomorrow, if anyone would like a free sample of my program, just make a pre-order for my new book. I may mention you in it of you tell me your tricks and trade secrets.
Re: 4.6250 piston in a stock 350 block
Posted: Sat Sep 30, 2017 2:50 pm
by Mark O'Neal
The equation doesn't work unless you use PI in it.
All good equations use PI....since it's an irrational number
Re: 4.6250 piston in a stock 350 block
Posted: Sat Sep 30, 2017 2:54 pm
by user-17438
Mark O'Neal wrote: ↑Sat Sep 30, 2017 2:50 pm
[The equation doesn't work unless you use PI in it.
All good equations use PI....since it's an irrational number[/b]
That's why I simplified this formula, so you don't need pi.. we just manipulate the data until the equation works.
Re: 4.6250 piston in a stock 350 block
Posted: Sat Sep 30, 2017 3:11 pm
by RevTheory
Who doesn't like pie?
Re: 4.6250 piston in a stock 350 block
Posted: Sat Sep 30, 2017 3:16 pm
by BigBlockMopar
Re: 4.6250 piston in a stock 350 block
Posted: Sat Sep 30, 2017 3:33 pm
by BigBlockMopar
SchmidtMotorWorks wrote: ↑Sat Sep 30, 2017 1:34 pm
Can you figure out how to put a 4.625 piston in a stock 350 block?
On a similar note, I would like to see someone come up with the proper way to install this 10" piston in a 426 Hemi...
Re: 4.6250 piston in a stock 350 block
Posted: Sat Sep 30, 2017 3:36 pm
by Keith Morganstein
One thing I forgot to mention, a 4,625" piston will make at least Twice (double) the horsepower in a 327 block VS a 350!
Re: 4.6250 piston in a stock 350 block
Posted: Sat Sep 30, 2017 3:45 pm
by user-17438
Only with stock headgaskets