Brake fluid question

Shocks, Springs, Brakes, Frame, Body Work, etc

Moderator: Team

Post Reply
User avatar
Posts: 377
Joined: Wed May 31, 2017 2:50 pm
Location: Lake Charles, LA

Brake fluid question

Post by nickpohlaandp » Tue Oct 10, 2017 10:04 pm

So I've been doing a lot of side work lately to find my project. Naturally that includes brake jobs. I'm thinking about building an auto bleeder out of one of those weed sprayer things. I'm curious, if I leave clean brake fluid will it be ok to store that way, or would I need to purge the container with some inert gas prior to storage to prevent it from collecting moisture? Thanks in advance for your help.
Never half ass two things... Whole ass one thing!

Brian P
Posts: 1222
Joined: Wed Jan 02, 2008 7:35 pm
Location: Toronto, Ontario, Canada

Re: Brake fluid question

Post by Brian P » Wed Oct 11, 2017 11:29 am

Storage in a sealed container is not a problem, long term storage with contact with the atmosphere will allow the fluid to absorb water.

Posts: 391
Joined: Thu Mar 21, 2013 12:03 pm
Location: Chancellorsville Battle Field, Chancellorsville, Virginia

Re: Brake fluid question

Post by BigBlocksOnTop2 » Wed Oct 11, 2017 4:59 pm

Napa stores are a good source for brake fittings.

Jeff Lee
Posts: 263
Joined: Sun Jun 26, 2011 1:20 am
Location: Anthem / Phoenix Arizona

Re: Brake fluid question

Post by Jeff Lee » Fri Nov 10, 2017 11:43 pm

I just redid my brake lines, or at least 75% of them. O’reilly Auto is very close to me. They did not have a fitting so I went down the road to NAPA. I was amazed at how much better the quality was for brake line fittings.
1970 AMX
390 4-speed
Advanced Clutches
Red Line Racing Cams

New Member
New Member
Posts: 5
Joined: Thu Jan 04, 2018 1:34 pm

Re: Brake fluid question

Post by AICLLC » Thu Jan 04, 2018 3:15 pm

Can you build a bladder separating the fluid from atmosphere?

dave brode
Posts: 663
Joined: Sun Sep 28, 2008 11:06 am
Location: Frostburg, MD

Re: Brake fluid question

Post by dave brode » Thu Jan 04, 2018 4:14 pm

Not automatic, but you can make bleeding MUCH easier, with a new clean oil squirt can and a turkey baster.

The oil can should have a pointy tube and be small enough for say 1/8" rubber "vacuum" hose to ppush onto it. The bigger the squirt can, the better.

1. Put several wraps of Teflon tape on the R/R bleeder. Use enough to make a seal between the bleeder and the wheel cyl/caliper body. With new fluid in squirt can, connect squirt hose to bleeder. A tie wrap on the bleeder end of hose is a good thing, but not 100% needed.

Start pumping new fluid into bleeder. The air and old fluid will be pushed to the mast cyl. Watch the mast cyl so not to run it over, and suck old dirty fluid out as needed with turkey baster. Re-fill squirt can often as needed, try not to run out and pump air. When new fluid appears in mast cyl, tighten bleeder, move to LR bleeder, repeat, repeat for both front bleeders.

One man operation. When you get done, Use a helper and do it the old way. You might get one little bubble of air from each bleeder, but often not.

Flush squirt can and turkey baster with soapy and save for next time.

Note that the teflon tape keep fluid from running out of the bleeder threads, and prevents sucking air between strokes.


Post Reply