Big bore short stroke vs. small bore long stroke
Moderator: Team
Re: Big bore short stroke vs. small bore long stroke
the answer is 42
Cheston Phillips
96 Impala SS
05 Silverado
96 Impala SS
05 Silverado
-
- Pro
- Posts: 201
- Joined: Sat Feb 20, 2010 10:53 am
- Location: Work: Houston, Home:Cypress
Re: Big bore short stroke vs. small bore long stroke
Look at an F1 engine.
The VOLT should have had a diesel engine...
Re:
...but only if you are valve area restricted... a 4-or 5-valve head most often are not, and they're a completely different ball game.stevek wrote:Big bore = more valve curtain area / higher breathing capacity
Small bore = sonic choke occurs at lower rpms than for big bore
-Bjørn
"Impossible? Nah...just needs more development time"
"Impossible? Nah...just needs more development time"
Re: Re:
Interesting and familiar topic. In the case of my single , 4 valve at 500 cc it started out with a 3.905" bore (99.2mm) and a 2.543" (64.6mm) stroke 30 ciSWR wrote:...but only if you are valve area restricted... a 4-or 5-valve head most often are not, and they're a completely different ball game.stevek wrote:Big bore = more valve curtain area / higher breathing capacity
Small bore = sonic choke occurs at lower rpms than for big bore
B/S ratio 1.535:1
R/S ratio 1.769:1
in stock form it makes about 34 hp to the rear wheels (atv)
450cc 4 valve bore 3.779 x 2.440 similar B/S , R/S and hp slightly higher
however the deck height is shorter.these engines accelerate quite fast .
I have a short distance to go and even shorter time to get there !
My single is 108mm x 70.6mm 114.47mm rod or 4.251" x 2.77" rod 4.5" also makes 45 ft. lbs @ 6800 rpm
37mm int. 32 mm exh.
My single is 108mm x 70.6mm 114.47mm rod or 4.251" x 2.77" rod 4.5" also makes 45 ft. lbs @ 6800 rpm
37mm int. 32 mm exh.
-
- Guru
- Posts: 15481
- Joined: Thu Feb 15, 2007 8:43 pm
- Location: Cypress, California
Re: Big bore short stroke vs. small bore long stroke
Just thinking about this thread and the EMC. If one had a particular block in mind to use for the EMC would it not be beneficial to bore it out to the safe maximum and then adjust the stroke to get the desired displacement? Is was thinking of something like the Dart SHP block.
- Stan Weiss
- Vendor
- Posts: 4820
- Joined: Tue Feb 20, 2007 1:31 pm
- Location: Philadelphia, PA
- Contact:
Re: Big bore short stroke vs. small bore long stroke
This might be the case if there was no RPM limit.1989TransAm wrote:Just thinking about this thread and the EMC. If one had a particular block in mind to use for the EMC would it not be beneficial to bore it out to the safe maximum and then adjust the stroke to get the desired displacement? Is was thinking of something like the Dart SHP block.
Stan
Stan Weiss/World Wide Enterprises
Offering Performance Software Since 1987
http://www.magneticlynx.com/carfor/carfor.htm
David Vizard & Stan Weiss' IOP / Flow / Induction Optimization Software
http://www.magneticlynx.com/DV
Offering Performance Software Since 1987
http://www.magneticlynx.com/carfor/carfor.htm
David Vizard & Stan Weiss' IOP / Flow / Induction Optimization Software
http://www.magneticlynx.com/DV
Re: Big bore short stroke vs. small bore long stroke
with 2 valve big bore drag V8's it seems most answers are written in stone (generally) however with single cylinder 4 valve engines I think the rules are still being written. slightly larger than 500cc, say 511cc bored and stroked engine making 70 hp/ 40 torque. 2.2 hp per cu. in. Bore size is limited to about 102 maybe 103 due to block/ bolt/cylinder spacing.
I don't know if it is over looked or what but a single with a real light piston can accelerate very fast more so than say a larger bore but a single piston kind of magnifies all details.of course when you bring F1 out as a trump card the rules are very different. still big bore small stroke long rod engine the pistons are small and very light. short crank throw very fast acceleration .
the drag of the piston rings and other parts become very critical when you have a single piston to depend on. IMHO.friction and reciprocating weight have got to be key factors.
I don't know if it is over looked or what but a single with a real light piston can accelerate very fast more so than say a larger bore but a single piston kind of magnifies all details.of course when you bring F1 out as a trump card the rules are very different. still big bore small stroke long rod engine the pistons are small and very light. short crank throw very fast acceleration .
the drag of the piston rings and other parts become very critical when you have a single piston to depend on. IMHO.friction and reciprocating weight have got to be key factors.
I have a short distance to go and even shorter time to get there !
My single is 108mm x 70.6mm 114.47mm rod or 4.251" x 2.77" rod 4.5" also makes 45 ft. lbs @ 6800 rpm
37mm int. 32 mm exh.
My single is 108mm x 70.6mm 114.47mm rod or 4.251" x 2.77" rod 4.5" also makes 45 ft. lbs @ 6800 rpm
37mm int. 32 mm exh.
-
- Pro
- Posts: 312
- Joined: Thu May 10, 2007 11:56 pm
- Location:
Re: Big bore short stroke vs. small bore long stroke
I have been told that in two single cylindar engines having the same displcement as example a 1" bore by a 120'' stroke, vers a 10.96" bore with a 1" stroke, and each engine being able to achieve the same amount of cylindar fill, both engines would make the same power but the short stroke engine would produce more useable energy output because of less friction in the ring pack and internal drag of the parts. I have also been told that the only subsute for cubic inches is cubic dollars.
Re: Big bore short stroke vs. small bore long stroke
in the mid to late 60s for built the 428, long stroke smaller piston,they specifcally built it to compete with thier own 427 bigger piston shorter stroke, but this was for basic street racing, on the track the 427 beats the 428,.gear ratio type of fuel compression, carburation,all factor in, to make the engines equal they would have to be built very differently and the cars would have to be built different also(gearing tire size)
old man old school hotrodder
-
- Member
- Posts: 69
- Joined: Tue Sep 04, 2012 3:35 am
- Location:
Re: Big bore short stroke vs. small bore long stroke
How much would the rpm need to increase going from a 4.100 stroke to a 4" stroke with same head and bore?
Would it be benificial to shorten the stroke with bore and valve size same between both?
58lb crank in both apps.
Would it be benificial to shorten the stroke with bore and valve size same between both?
58lb crank in both apps.
Re: Big bore short stroke vs. small bore long stroke
unless your rules favor small inches or restrict you in some way go with the cubic inches. Cubic inches wins every time, I would never intentionally make an engine smaller unless there was a weight/cubic inch rule or a cubic inch maximum.mustangcobra438 wrote:How much would the rpm need to increase going from a 4.100 stroke to a 4" stroke with same head and bore?
Would it be benificial to shorten the stroke with bore and valve size same between both?
58lb crank in both apps.
Big cubic inches is much harder to make the hp/cubic inch target with which is why you see a lot of small engines at Engine Master's Challenge but the larger motors will make more overall power/torque and do it with less rpm which means reliability/longevity.
Re: Big bore short stroke vs. small bore long stroke
I agree,900HP wrote:unless your rules favor small inches or restrict you in some way go with the cubic inches. Cubic inches wins every time, I would never intentionally make an engine smaller unless there was a weight/cubic inch rule or a cubic inch maximum.mustangcobra438 wrote:How much would the rpm need to increase going from a 4.100 stroke to a 4" stroke with same head and bore?
Would it be benificial to shorten the stroke with bore and valve size same between both?
58lb crank in both apps.
Big cubic inches is much harder to make the hp/cubic inch target with which is why you see a lot of small engines at Engine Master's Challenge but the larger motors will make more overall power/torque and do it with less rpm which means reliability/longevity.
I'm just a dumb Millwright with a dyno, but for a street/strip motor I'll take a mild large displacement engine any day. You can't argue with torque and big motors make big torque. My mild 605 truck motor makes 765ftlbs.@3500rpm (start of the dyno pull) and peaks at 818@4800rpm and holds 800+ till after 5500rpm.Dave
[img]http://img.photobucket.com/albums/v514/quickd100/9ff3c690.jpg[/img]
-
- Member
- Posts: 69
- Joined: Tue Sep 04, 2012 3:35 am
- Location:
Re: Big bore short stroke vs. small bore long stroke
What about parasitic loses form longer stroke and windage as well as longer stroke being harder in engine from weight rotating farther out?900HP wrote:unless your rules favor small inches or restrict you in some way go with the cubic inches. Cubic inches wins every time, I would never intentionally make an engine smaller unless there was a weight/cubic inch rule or a cubic inch maximum.mustangcobra438 wrote:How much would the rpm need to increase going from a 4.100 stroke to a 4" stroke with same head and bore?
Would it be benificial to shorten the stroke with bore and valve size same between both?
58lb crank in both apps.
Big cubic inches is much harder to make the hp/cubic inch target with which is why you see a lot of small engines at Engine Master's Challenge but the larger motors will make more overall power/torque and do it with less rpm which means reliability/longevity.
Would longer stroke still prevail in same scenario as mentioned before?
I should mention this is a nmca na10.5 type motor but current block won't allow more than 4.125 bore without rpm causing cylinders to move around.
Re: Big bore short stroke vs. small bore long stroke
Honda uses a longer stroke than most the competition especially in Acura 4 cylinder engines. Some of 2-2.2 liters fours have strokes near 3.5 inches with a redline of over 8000 rpm. Now there might be emission or packaging considerations... But Honda is known for high RPM engines so they might know something...
Motorcycle land speed racing... wearing animal hides and clinging to vibrating oily machines propelled by fire
Re: Big bore short stroke vs. small bore long stroke
I'm not saying a long stroke "prevails" I'm saying cubic inches prevail. If you are limited to a 4.125" bore, you WILL make more power/torque with a 4.100" stroke than with a 4.00" stroke because you have more cubic inches. You will not make the horsepower per cubic inch with the larger motor but you will make more power overall.mustangcobra438 wrote:What about parasitic loses form longer stroke and windage as well as longer stroke being harder in engine from weight rotating farther out?900HP wrote:unless your rules favor small inches or restrict you in some way go with the cubic inches. Cubic inches wins every time, I would never intentionally make an engine smaller unless there was a weight/cubic inch rule or a cubic inch maximum.mustangcobra438 wrote:How much would the rpm need to increase going from a 4.100 stroke to a 4" stroke with same head and bore?
Would it be benificial to shorten the stroke with bore and valve size same between both?
58lb crank in both apps.
Big cubic inches is much harder to make the hp/cubic inch target with which is why you see a lot of small engines at Engine Master's Challenge but the larger motors will make more overall power/torque and do it with less rpm which means reliability/longevity.
Would longer stroke still prevail in same scenario as mentioned before?
I should mention this is a nmca na10.5 type motor but current block won't allow more than 4.125 bore without rpm causing cylinders to move around.