Re: Ported Dart 215's with port energy discussion 3.0

General engine tech -- Drag Racing to Circle Track

Moderator: Team

Post Reply
Carnut1
Guru
Guru
Posts: 3805
Joined: Tue Jun 11, 2013 6:32 pm
Location: Melbourne fl.

Re: Ported Dart 215's with port energy discussion 3.0

Post by Carnut1 » Fri May 11, 2018 5:27 am

https://www.speedtalk.com/forum/viewtop ... =1&t=44136 This should be the second thread. Thanks, Charlie
Servedio Cylinder Head Development
631-816-4911
9:00am - 9:00pm EST

steve cowan
Expert
Expert
Posts: 569
Joined: Wed Jul 27, 2011 5:22 am
Location: brisbane AUSTRALIA

Re: Ported Dart 215's with port energy discussion 3.0

Post by steve cowan » Fri May 11, 2018 5:42 am

thanks charlie,
i remember that thread,what are your thoughts now,maybe smaller throat % on the intake??
did you use course sanding rolls or stones to finish on those ones?
interesting picture with the dyekem out of the intake heading through the chamber
any secrets you want to share :D
i have not measured my sport 2s as they are on the 327 at the moment,i will keep the 2.02 in valve and work from there,what do you think would be a fair # for a 2.02 valve,64cc chamber,i did cc the intake it is approx 204cc from memory,it will be a while before i do anything with the the sports 2 as i got a bit on at the moment,but i am keen to get some data as cast.
thanks for your input charlie,
steve c

Carnut1
Guru
Guru
Posts: 3805
Joined: Tue Jun 11, 2013 6:32 pm
Location: Melbourne fl.

Re: Ported Dart 215's with port energy discussion 3.0

Post by Carnut1 » Fri May 11, 2018 8:15 am

steve cowan wrote:
Fri May 11, 2018 5:42 am
thanks charlie,
i remember that thread,what are your thoughts now,maybe smaller throat % on the intake??
did you use course sanding rolls or stones to finish on those ones?
interesting picture with the dyekem out of the intake heading through the chamber
any secrets you want to share :D
i have not measured my sport 2s as they are on the 327 at the moment,i will keep the 2.02 in valve and work from there,what do you think would be a fair # for a 2.02 valve,64cc chamber,i did cc the intake it is approx 204cc from memory,it will be a while before i do anything with the the sports 2 as i got a bit on at the moment,but i am keen to get some data as cast.
thanks for your input charlie,
I was measuring throat ratio wrong they are much closer to 90%. SP2's are about 235 cfm untouched and can go 300 + with work. Start your own thread and get some real input on how many cfm that engine needs to get to your goal. I ran a 200+ cc bowtie on a 383 for a long time, hard running mill.
Servedio Cylinder Head Development
631-816-4911
9:00am - 9:00pm EST

MELWAY
Expert
Expert
Posts: 789
Joined: Mon Dec 04, 2006 7:37 pm
Location: melbourne australia

Re: Ported Dart 215's with port energy discussion 3.0

Post by MELWAY » Sat May 12, 2018 6:22 am

Sportsman 2 are probably the best cast 23deg head for a 355-383” engine. When they are preped right
3370lb Sedan 9.89@136MPH 358chevN/A

steve cowan
Expert
Expert
Posts: 569
Joined: Wed Jul 27, 2011 5:22 am
Location: brisbane AUSTRALIA

Re: Ported Dart 215's with port energy discussion 3.0

Post by steve cowan » Sat May 12, 2018 6:34 am

James,
I know back in the day, your hg-ht ran really hard,
I hope you can give me some tips down the track when time comes,
steve c

Post Reply