I was assembling an engine today and I noticed the rod bearing was riding up to the radius on the crank. The bearings do not have enough champher.
I have a lathe and can cut one but I need the fixture to hold the bearings.
Anyone have an idea where I can get a fixture?
Thanks
Dave
Rod Bearing Champher
Moderator: Team
-
- Guru
- Posts: 2151
- Joined: Fri Apr 07, 2006 8:23 pm
- Location:
- Dave Koehler
- Vendor
- Posts: 7207
- Joined: Mon Oct 04, 2004 11:19 pm
- Location: Urbana, IL USA
- Contact:
Dave,
In your neigborhood. http://www.precisionmeasure.com/block8.htm
If all else fails, I can machine them if you need.
Later
Dave Koehler
www.koehlerinjection.com
In your neigborhood. http://www.precisionmeasure.com/block8.htm
If all else fails, I can machine them if you need.
Later
Dave Koehler
www.koehlerinjection.com
Dave Koehler - Koehler Injection
Enderle Fuel Injection - Nitrous Charger - Balancing - Nitrous Master software
http://www.koehlerinjection.com
"Never let a race car know that you are in a hurry."
Enderle Fuel Injection - Nitrous Charger - Balancing - Nitrous Master software
http://www.koehlerinjection.com
"Never let a race car know that you are in a hurry."
-
- Guru
- Posts: 2651
- Joined: Sun Sep 05, 2004 6:38 pm
- Location: salt lake city, ut
- Contact:
-you could use a piece of some sort of plastic or pvc pipe etc---chuck up a short piece and machine the OD leaving a step to align the bearings---the diameter to fit the bearings in their natural state--then use a simple radiator hose clamp to hold the bearing shells to the plastic.
-Takes about 5 minutes to make this if you have the something to make it out of.
-Takes about 5 minutes to make this if you have the something to make it out of.
-
- Pro
- Posts: 479
- Joined: Sun Jun 11, 2006 6:24 pm
- Location: OHIO
- Contact:
These guys also make bearing narrowing fixtures
R&R racing ask for Mike
http://www.rrconnectingrods.com/about.htm
Makes some damn fine billet steel and aluminum rods as well
http://www.rrconnectingrods.com/brackets.htm
TI
http://www.rrconnectingrods.com/about.htm
Makes some damn fine billet steel and aluminum rods as well
http://www.rrconnectingrods.com/brackets.htm
TI
TORQUE RULES !!!!
I must be getting old because attaching them on the outside of something didn't even enter my mind.... Thanks Bill.
Rustbucket, I knew FM has the bearing and I knew this crank has a large radius so this falls on me for not ordering the right bearings to start with all I can say is see the above first sentence... LOL
Dave, Thanks for the link and I will call them Tuesday and get a fixture on the way but meanwhile I think I will give Bills idea a shot. Beats sitting here in the ice with nothing to do. Except wait on UPS to find me....
Thanks to all for the info and advice. That's why I like this site. Mostly I just read but I have never failed to get a workable solution when I have a question.
Dave
Rustbucket, I knew FM has the bearing and I knew this crank has a large radius so this falls on me for not ordering the right bearings to start with all I can say is see the above first sentence... LOL
Dave, Thanks for the link and I will call them Tuesday and get a fixture on the way but meanwhile I think I will give Bills idea a shot. Beats sitting here in the ice with nothing to do. Except wait on UPS to find me....
Thanks to all for the info and advice. That's why I like this site. Mostly I just read but I have never failed to get a workable solution when I have a question.
Dave
- Dave Koehler
- Vendor
- Posts: 7207
- Joined: Mon Oct 04, 2004 11:19 pm
- Location: Urbana, IL USA
- Contact:
My procedure when using Bills time honored method.
1: install bearing in connecting rod and measure the ID.
2: chuck up some nylon round or some other plastic stock larger than your bearing OD. The larger OD is so that you leave a wall for the back edge of the bearing to seat against. This will line up both halves easily.
3: machine round stock .0005 to .001 larger than your measured ID. It doesn't take much to hold it since you are not doing serious hogging.
4: machine the width where the bearing clamps less than your bearing width so that the champher sticks out enough for you to machine it.
5: hose clamp it and go to work.
6: Oh, and pay close attention to which side of the bearing you want to machine.
A little history on the female clamp that is available.
As I recall, Barry Little at Specialty Automotive Engineering (SAE) was the originator of these, circa 1980. He quit making them so I made them for a while in the 90s, then Adrian at Precision started making them. I now see R&R does also.
Dave Koehler
www.koehlerinjection.com
1: install bearing in connecting rod and measure the ID.
2: chuck up some nylon round or some other plastic stock larger than your bearing OD. The larger OD is so that you leave a wall for the back edge of the bearing to seat against. This will line up both halves easily.
3: machine round stock .0005 to .001 larger than your measured ID. It doesn't take much to hold it since you are not doing serious hogging.
4: machine the width where the bearing clamps less than your bearing width so that the champher sticks out enough for you to machine it.
5: hose clamp it and go to work.
6: Oh, and pay close attention to which side of the bearing you want to machine.
A little history on the female clamp that is available.
As I recall, Barry Little at Specialty Automotive Engineering (SAE) was the originator of these, circa 1980. He quit making them so I made them for a while in the 90s, then Adrian at Precision started making them. I now see R&R does also.
Dave Koehler
www.koehlerinjection.com
Dave Koehler - Koehler Injection
Enderle Fuel Injection - Nitrous Charger - Balancing - Nitrous Master software
http://www.koehlerinjection.com
"Never let a race car know that you are in a hurry."
Enderle Fuel Injection - Nitrous Charger - Balancing - Nitrous Master software
http://www.koehlerinjection.com
"Never let a race car know that you are in a hurry."
-
- Guru
- Posts: 2651
- Joined: Sun Sep 05, 2004 6:38 pm
- Location: salt lake city, ut
- Contact:
-just for sh-ts and grins I just made up a plastic piece like I described and touched up the chamfers on a set of used BBC bearings---just to get the dimensions I'd use.
-The bearing shells need to just slightly expand to snap onto a 2.285" diameter snout---which is sort of nice because you can just pop'm on there and they stay put while you install the hose clamp.
-I put the step back at .710" and that leaves you enough room to get your lathe tool in there and to be able to see all of the chamfered area.
-The OD of the fixture needs to be 2.375" as a minimum for the step.
-Took about 5 minutes to make the fixture and chamfer the one pair of shells.
--------------------------------------------------------------------------------------
-Years ago I took 3 sizes of Chevrolet rods-----cut the beams off with a bandsaw and ground'm sort of smooth----chucked each rod up in the lathe and machined the outside side edges of the rods round----to where I had enough an area to grip'm in my lathe jaws.
-Then I tack welded the head of the rod bolts to rods---removed the nuts & the rod caps and cut the bolt off to where I had about 7/16" of the rod bolt left to act as a dowel for the rod cap.
-Those have served me well for 30 years.
-------------------------------------------------------------------------------------
-The only problem with the larger diameter of the plastic part is there is gap which means that if you wanted to do a hand scrape with a deburr tool you wouldn't be able to.
-------------------------------------------------------------------------------------
-I have photos of both a modified BBC rod and this plastic part if anybody is interested.
-photos are available at http://ryanbrownracing.com/Bill_Jones_Page_20.html
-The bearing shells need to just slightly expand to snap onto a 2.285" diameter snout---which is sort of nice because you can just pop'm on there and they stay put while you install the hose clamp.
-I put the step back at .710" and that leaves you enough room to get your lathe tool in there and to be able to see all of the chamfered area.
-The OD of the fixture needs to be 2.375" as a minimum for the step.
-Took about 5 minutes to make the fixture and chamfer the one pair of shells.
--------------------------------------------------------------------------------------
-Years ago I took 3 sizes of Chevrolet rods-----cut the beams off with a bandsaw and ground'm sort of smooth----chucked each rod up in the lathe and machined the outside side edges of the rods round----to where I had enough an area to grip'm in my lathe jaws.
-Then I tack welded the head of the rod bolts to rods---removed the nuts & the rod caps and cut the bolt off to where I had about 7/16" of the rod bolt left to act as a dowel for the rod cap.
-Those have served me well for 30 years.
-------------------------------------------------------------------------------------
-The only problem with the larger diameter of the plastic part is there is gap which means that if you wanted to do a hand scrape with a deburr tool you wouldn't be able to.
-------------------------------------------------------------------------------------
-I have photos of both a modified BBC rod and this plastic part if anybody is interested.
-photos are available at http://ryanbrownracing.com/Bill_Jones_Page_20.html
Last edited by bill jones on Fri Feb 23, 2007 8:58 pm, edited 1 time in total.