390/428 FE Strokers

General engine tech -- Drag Racing to Circle Track

Moderator: Team

blykins
Guru
Guru
Posts: 2098
Joined: Mon Aug 27, 2007 8:59 pm
Location: Louisville, KY

Re: 390/428 FE Strokers

Postby blykins » Sat Aug 12, 2017 7:54 am

I don't know how many 4.250" cranks I've used in FE's.....uncountable. Never had a rod/cam issue. It starts getting close with a 4.375" crank, but with the right rod, there's still enough clearance.

I think you have something else going on. Some of the older Scat cranks had counterweights that were misshapen. They were contacting the wrist pin bosses on the pistons. Check that first...
Lykins Motorsports
brent@lykinsmotorsports.com
www.lykinsmotorsports.com

bigjoe1
Show Guest
Show Guest
Posts: 6104
Joined: Thu Aug 24, 2006 7:16 pm
Location: santa ana calif-92703
Contact:

Re: 390/428 FE Strokers

Postby bigjoe1 » Sat Aug 12, 2017 10:00 am

GIVE THE MAN A CIGAR ! That is what it was==



JOE SHERMAN RACING

blykins
Guru
Guru
Posts: 2098
Joined: Mon Aug 27, 2007 8:59 pm
Location: Louisville, KY

Re: 390/428 FE Strokers

Postby blykins » Sat Aug 12, 2017 10:05 am

Little harder to fix, but glad you got it nailed down.
Lykins Motorsports
brent@lykinsmotorsports.com
www.lykinsmotorsports.com

PackardV8
Guru
Guru
Posts: 4923
Joined: Sun Jul 30, 2006 1:03 pm

Re: 390/428 FE Strokers

Postby PackardV8 » Sat Aug 12, 2017 10:21 am

Glad you got good advice on exactly where to look. That counterweight to piston clearance thing once nearly drove me nuts on a Packard V8 being run in before being shipped to England. Good thing we did run it, as there was a noise which got louder as it warmed. Pulled the pan, pulled the rod bearings and rechecked the bearing clearances. Stock cam and crank, so no interference there. Finally, I saw a smudge of aluminum on a counterweight. These were aftermarket cast stock replacement pistons and had always cleared before, so I had looked everywhere else first for that little knock. The piston skirts were left as cast and one edge was barely ticking against one counterweight. Six extra hours of shop time, two minutes with a half-round file, a new pan gasket and the Packard V8 was on the way to England.
Jack Vines
Studebaker-Packard V8 Limited
Obsolete Engineering

bigjoe1
Show Guest
Show Guest
Posts: 6104
Joined: Thu Aug 24, 2006 7:16 pm
Location: santa ana calif-92703
Contact:

Re: 390/428 FE Strokers

Postby bigjoe1 » Sat Aug 12, 2017 12:07 pm

A good friend at SCAT told me where to look-- Thanks guys !



JOE SHERMAN RACING

My427stang
Expert
Expert
Posts: 633
Joined: Fri Sep 09, 2005 10:04 pm
Location: Omaha, NE
Contact:

Re: 390/428 FE Strokers

Postby My427stang » Sat Aug 12, 2017 6:36 pm

Good stuff, Brent sure has lugged a few SCAT FE cranks across the shop!
70 Mustang, 489 FE, TKO-600, Massflo SEFI, 4.11s
71 F100 SB 4x4, 445 FE, hot rod 4x4

blykins
Guru
Guru
Posts: 2098
Joined: Mon Aug 27, 2007 8:59 pm
Location: Louisville, KY

Re: 390/428 FE Strokers

Postby blykins » Sun Aug 13, 2017 11:07 am

If the aftermarket FE block quality doesn't go up, I won't be lugging any more. 'Bout done with them.
Lykins Motorsports
brent@lykinsmotorsports.com
www.lykinsmotorsports.com


Return to “Engine Tech”

Who is online

Users browsing this forum: Exabot [Bot], GARY C, Google [Bot], KnightEngines, Yahoo [Bot] and 15 guests