Another "How much will it make?" Project "Special Needs"

General engine tech -- Drag Racing to Circle Track

Moderator: Team

Post Reply
Olds455
New Member
New Member
Posts: 47
Joined: Thu Mar 29, 2018 8:18 pm

Re: Another "How much will it make?" Project "Special Needs"

Post by Olds455 » Thu Nov 29, 2018 5:39 am

=D>

You people are more petty than 13 yr old girls that just got their feelingZ hurt.

steve cowan
Expert
Expert
Posts: 646
Joined: Wed Jul 27, 2011 5:22 am
Location: brisbane AUSTRALIA

Re: Another "How much will it make?" Project "Special Needs"

Post by steve cowan » Thu Nov 29, 2018 5:40 am

C H A D
good luck on the dyno this weekend,i think 585- 590 hp would be expected and i hope it goes to 600,this is a an extremely strong engine and at 10.5 :1 comp on pump gas with a HR cam is nothing short of amazing,big credit to all involved.
this is one of my favorite threads and i have read all 42 pages 3 times over,it has all the right ingredients-
FUN
FACTS
FICTION
i understand you will be busy on the dyno but some video footage would be greatly appreciated,looking forward to the post dyno dissection :D
steve c

CGT
Guru
Guru
Posts: 1424
Joined: Sun May 10, 2009 12:29 pm

Re: Another "How much will it make?" Project "Special Needs"

Post by CGT » Thu Nov 29, 2018 10:25 am

Well hopefully the dissection involves comparing numbers and not broken stuff. Im ready to be done with this engine and move on to something different...
And so is my '65'
Resized_20160605_165857001.jpg
Resized_20160605_170203001.jpg
Resized_20160605_170153001.jpg
Resized_20160605_165905001.jpg
You do not have the required permissions to view the files attached to this post.
"How or Y do you think I get all this $hit, I read all of you all builds and desktop dyno them with all the correct info and I've got your build."

steve cowan
Expert
Expert
Posts: 646
Joined: Wed Jul 27, 2011 5:22 am
Location: brisbane AUSTRALIA

Re: Another "How much will it make?" Project "Special Needs"

Post by steve cowan » Thu Nov 29, 2018 11:48 am

CGT wrote:
Thu Nov 29, 2018 10:25 am
Well hopefully the dissection involves comparing numbers and not broken stuff. Im ready to be done with this engine and move on to something different...
And so is my '65'
Resized_20160605_165857001.jpg
Resized_20160605_170203001.jpg
Resized_20160605_170153001.jpg
Resized_20160605_165905001.jpg
damn she is a sweet ride
steve c

novadude
Guru
Guru
Posts: 1313
Joined: Thu Oct 11, 2007 3:24 pm
Location: Shippensburg, PA

Re: Another "How much will it make?" Project "Special Needs"

Post by novadude » Thu Nov 29, 2018 1:07 pm

That's a good looking chassis!

zums
Guru
Guru
Posts: 1258
Joined: Sat Dec 08, 2007 10:57 am
Location: south jersey

Re: Another "How much will it make?" Project "Special Needs"

Post by zums » Thu Nov 29, 2018 6:40 pm

Nice!
Tom

CGT
Guru
Guru
Posts: 1424
Joined: Sun May 10, 2009 12:29 pm

Re: Another "How much will it make?" Project "Special Needs"

Post by CGT » Thu Nov 29, 2018 8:44 pm

zums wrote:
Thu Nov 29, 2018 6:40 pm
Nice!
Tom
Thanks. Whats your 65 run?
"How or Y do you think I get all this $hit, I read all of you all builds and desktop dyno them with all the correct info and I've got your build."

zums
Guru
Guru
Posts: 1258
Joined: Sat Dec 08, 2007 10:57 am
Location: south jersey

Re: Another "How much will it make?" Project "Special Needs"

Post by zums » Thu Nov 29, 2018 9:41 pm

CGT wrote:
Thu Nov 29, 2018 8:44 pm
zums wrote:
Thu Nov 29, 2018 6:40 pm
Nice!
Tom
Thanks. Whats your 65 run?
11.1 through full exhaust, 92 pump gas small vales, track has a 11 second roll cage rule, through me out after second run, id be a fool if i couldnt tune a few tenths with open exhaust, so i tagged it, nice stress relief machine, lol
Tom

CGT
Guru
Guru
Posts: 1424
Joined: Sun May 10, 2009 12:29 pm

Re: Another "How much will it make?" Project "Special Needs"

Post by CGT » Thu Nov 29, 2018 10:53 pm

Stock suspenion? Auto?
"How or Y do you think I get all this $hit, I read all of you all builds and desktop dyno them with all the correct info and I've got your build."

zums
Guru
Guru
Posts: 1258
Joined: Sat Dec 08, 2007 10:57 am
Location: south jersey

Re: Another "How much will it make?" Project "Special Needs"

Post by zums » Fri Nov 30, 2018 2:35 pm

CGT wrote:
Thu Nov 29, 2018 10:53 pm
Stock suspenion? Auto?
Not completely, stock 6 cylinder springs in rear, South Side machine lower control arms so i can adjust pinion angle, i welded the top arms, and moroso springs in front, 350 turbo trans
Tom

CGT
Guru
Guru
Posts: 1424
Joined: Sun May 10, 2009 12:29 pm

Re: Another "How much will it make?" Project "Special Needs"

Post by CGT » Fri Nov 30, 2018 6:41 pm

Resized_20181130_152706.jpg
Resized_20181130_152716.jpg
You do not have the required permissions to view the files attached to this post.
"How or Y do you think I get all this $hit, I read all of you all builds and desktop dyno them with all the correct info and I've got your build."

Carnut1
Guru
Guru
Posts: 3991
Joined: Tue Jun 11, 2013 6:32 pm
Location: Melbourne fl.

Re: Another "How much will it make?" Project "Special Needs"

Post by Carnut1 » Sat Dec 01, 2018 7:32 am

Looks great! Please take a video, we want to hear it! Thanks, Charlie
Servedio Cylinder Head Development
631-816-4911
9:00am - 9:00pm EST

steve cowan
Expert
Expert
Posts: 646
Joined: Wed Jul 27, 2011 5:22 am
Location: brisbane AUSTRALIA

Re: Another "How much will it make?" Project "Special Needs"

Post by steve cowan » Fri Dec 07, 2018 1:02 pm

CGT wrote:
Fri Nov 30, 2018 6:41 pm
Resized_20181130_152706.jpgResized_20181130_152716.jpg
Hi C H A D,
How did SN go on the dyno? :D
steve c

CGT
Guru
Guru
Posts: 1424
Joined: Sun May 10, 2009 12:29 pm

Re: Another "How much will it make?" Project "Special Needs"

Post by CGT » Fri Dec 07, 2018 3:39 pm

It went well Steve. Well kinda. I have all the data in excel...thanks slo-svt. I've been reviewing it off and on. I'm real happy with the engine. Shoot me a PM with your email and I'll send some stuff your way. I can't figure out how post it on the forum.
"How or Y do you think I get all this $hit, I read all of you all builds and desktop dyno them with all the correct info and I've got your build."

Post Reply