"Durasurf" metal treatment process

General engine tech -- Drag Racing to Circle Track

Moderator: Team

seattle smitty
Member
Member
Posts: 90
Joined: Fri Oct 05, 2007 5:06 pm
Location:

"Durasurf" metal treatment process

Post by seattle smitty »

In the Seventies there was a metal finishing process, developed by William H. Davis of Tenafly, NJ, with the company Durasurf, Inc. headquartered at 75 Carver Ave., Westwood, NJ. After extensive searching, I can find no current info on any of this. My interest is from an old clipping from the April, 1976 issue of Hot Rod, Pg73+. This describes Davis' process of metal finishing via chemicals and abraisives and ultrasonics at an uncommon frequency and amplitude. The surface finish achieved, on such things as valves and valve springs, among many applications, was said to greatly improve fatigue resistance of these parts. Reportedly some racing teams were finding it useful.

Anybody here know anything about this. in searching, about all I can find is that Davis' trademark protection expired long ago, and that a William H. Davis of Tenafly, NJ died in the late Ninties, although there may be another by the same name, age 87, still alive, so I don't know. From what little I can gather, this was possibly a smart guy with a good process that has been discontinued and not picked up by any other outfit. I didn't see any patent info.
Kevin Johnson
HotPass
HotPass
Posts: 9365
Joined: Tue Nov 22, 2005 5:41 am
Location:

Re: "Durasurf" metal treatment process

Post by Kevin Johnson »

Driving Force Online: BREAKING NEWS—Ohio Governor Signs SEMA-Supported Vehicle Freedom Bill Into Law!
autogear
Vendor
Posts: 536
Joined: Thu Dec 08, 2011 9:03 am
Location:

Re: "Durasurf" metal treatment process

Post by autogear »

I wonder if it is akin to the REM (tm) polishing process. We use a similar, albeit waterbased process on our gears, shafts and sliding clutches.
vwchuck
Expert
Expert
Posts: 702
Joined: Thu May 28, 2009 11:06 pm
Location:

Re: "Durasurf" metal treatment process

Post by vwchuck »

Yea sounds like the 70's version of isotropic surface finishing or REM as stated above.
Kevin Johnson
HotPass
HotPass
Posts: 9365
Joined: Tue Nov 22, 2005 5:41 am
Location:

Re: "Durasurf" metal treatment process

Post by Kevin Johnson »

https://en.wikipedia.org/wiki/Vibratory_stress_relief might be the uncommon frequency and amplitude (varying for different items). Two birds with one vibrating abrasive.

~~~~~~~~~~

http://www.dhmo.org/truth/Dihydrogen-Monoxide.html

"Better Things for Better Living...Through Chemistry." DuPont
Driving Force Online: BREAKING NEWS—Ohio Governor Signs SEMA-Supported Vehicle Freedom Bill Into Law!
User avatar
MadBill
Guru
Guru
Posts: 15024
Joined: Tue Nov 15, 2005 10:41 am
Location: The Great White North

Re: "Durasurf" metal treatment process

Post by MadBill »

Nasty stuff that DHMO, and incredibly addictive... :shock:
Felix, qui potuit rerum cognscere causas.

Happy is he who can discover the cause of things.
pdq67
Guru
Guru
Posts: 9841
Joined: Thu Mar 04, 2010 8:05 pm
Location:

Re: "Durasurf" metal treatment process

Post by pdq67 »

Probably not applicable, but I remember reading about guys clamping engine parts like heads, cranks, blocks and such to a great big adjustable vibrating table and "shaking" hell out of them to stress relieve them. They would tune the vibration frequencies to do this....

Just food for thought.

pdq67
kirkwoodken
Guru
Guru
Posts: 1541
Joined: Thu Dec 06, 2007 11:35 pm
Location:

Re: "Durasurf" metal treatment process

Post by kirkwoodken »

Looks like Kevin hit the nail on the head! I believe that chemistry is still sold by Kale Auto Division. They sell the pure stuff, not the watered down version, as do some other dealers.
"Life is too short to not run a solid roller cam."
"Anything is possible, if you don't know what you're talking about."
I am NOT an Expert, and DEFINITELY NOT a GURU.
Kirkwoodken
Cubic_Cleveland
Guru
Guru
Posts: 1163
Joined: Thu Feb 23, 2012 11:44 pm
Location: Australia

Re: "Durasurf" metal treatment process

Post by Cubic_Cleveland »

pdq67 wrote:Probably not applicable, but I remember reading about guys clamping engine parts like heads, cranks, blocks and such to a great big adjustable vibrating table and "shaking" hell out of them to stress relieve them. They would tune the vibration frequencies to do this....

Just food for thought.

pdq67
Still a widely used process today. http://www.meta-lax.com
seattle smitty
Member
Member
Posts: 90
Joined: Fri Oct 05, 2007 5:06 pm
Location:

Re: "Durasurf" metal treatment process

Post by seattle smitty »

Well, I looked at all of your links and references, and none of them sound to me like they are the same as Durasurf (which is not to say that any one of them might be equally effective or even better). www.remchem.com describes its process in such general terms as to tell me nothing. As for shaker tables, that's a whole different principle, whole-part stress relief rather than surface finishing. The late Joe Mondello became a big advocate of shaker tables (which operate at about 100Hz, not ultrasonic), as you can read about on www.mondello.com/page23.php

Given the age of the HRM article, it probably will take an OLD guy to tell us about this.
Kevin Johnson
HotPass
HotPass
Posts: 9365
Joined: Tue Nov 22, 2005 5:41 am
Location:

Re: "Durasurf" metal treatment process

Post by Kevin Johnson »

seattle smitty wrote:Well, I looked at all of your links and references, and none of them sound to me like they are the same as Durasurf (which is not to say that any one of them might be equally effective or even better). http://www.remchem.com describes its process in such general terms as to tell me nothing. As for shaker tables, that's a whole different principle, whole-part stress relief rather than surface finishing. The late Joe Mondello became a big advocate of shaker tables (which operate at about 100Hz, not ultrasonic), as you can read about on http://www.mondello.com/page23.php

Given the age of the HRM article, it probably will take an OLD guy to tell us about this.

You just have to go to Remchem's 1984 patent to learn more about it: http://www.google.com/patents/US4491500 You can follow their citations and also explore some of their later patents.

They don't specifically mention electropolishing which has been around a long time: http://palmettoplating.com/wp-content/u ... -Paper.pdf

https://www.google.com/#q=ultrasonic+electropolishing you can explore ultrasonic additions to electropolishing.

https://www.google.com/#q=ultrasonic+stress+relief ultrasonic stress relief.

A few dozens of lifetimes of study wrapped in there.
Driving Force Online: BREAKING NEWS—Ohio Governor Signs SEMA-Supported Vehicle Freedom Bill Into Law!
seattle smitty
Member
Member
Posts: 90
Joined: Fri Oct 05, 2007 5:06 pm
Location:

Re: "Durasurf" metal treatment process

Post by seattle smitty »

Thanks for all that, Kevin, I'll take a look.
Edgottoys
New Member
New Member
Posts: 2
Joined: Wed Jun 13, 2018 7:24 am
Location:

Re: "Durasurf" metal treatment process

Post by Edgottoys »

I have read a few posts about Durasurf. Does anyone know what Durasurf and BMW motorcycles have in common back in the early to mid 1970's. I have read something about Durasurf putting there product on a BMW motorcycle. Does anyone have information about this?
Krooser
Guru
Guru
Posts: 1857
Joined: Wed Jul 31, 2013 10:14 pm
Location: Tropical Wisconsin

Re: "Durasurf" metal treatment process

Post by Krooser »

pdq67 wrote: Mon Aug 24, 2015 10:26 pm Probably not applicable, but I remember reading about guys clamping engine parts like heads, cranks, blocks and such to a great big adjustable vibrating table and "shaking" hell out of them to stress relieve them. They would tune the vibration frequencies to do this....

Just food for thought.

pdq67
I used to have a girlfriend that could do that...
Honored to be a member of the Luxemburg Speedway Hall of Fame Class of 2019
Edgottoys
New Member
New Member
Posts: 2
Joined: Wed Jun 13, 2018 7:24 am
Location:

Re: "Durasurf" metal treatment process

Post by Edgottoys »

I have come across a motorcycle from the mid 70's that has" Durasurf "painted on the fuel tank it appears to be professionally done. I'm looking for any information on this motorcycle and the conection to Durasurf.
Post Reply