Search found 190 matches
- Wed Feb 21, 2018 5:02 am
- Forum: Engine Tech
- Topic: DSS 427 SB Ford build
- Replies: 85
- Views: 15293
Re: DSS 427 SB Ford build
Did this build ever get completed ?
- Tue Mar 28, 2017 9:27 pm
- Forum: Engine Tech
- Topic: Vizard 427 SBF Rear Main Seal Dilemma
- Replies: 43
- Views: 10883
Re: Vizard 427 SBF Rear Main Seal Dilemma
David,
Does GST seals make the rear 1pc seal for DART Iron Eagle FORD block yet? Can you run these low friction seals without a vac pump for street use?
Does GST seals make the rear 1pc seal for DART Iron Eagle FORD block yet? Can you run these low friction seals without a vac pump for street use?
- Mon Mar 06, 2017 3:05 am
- Forum: Engine Tech
- Topic: Cleveland road race cam - 2nd opinion required
- Replies: 73
- Views: 12372
Re: Cleveland road race cam - 2nd opinion required
Nice Job on the engine! How much timing did it take?
Spark plug heat range?
Spark plug heat range?
- Sun Mar 05, 2017 8:39 pm
- Forum: Engine Tech
- Topic: Cleveland road race cam - 2nd opinion required
- Replies: 73
- Views: 12372
Re: Cleveland road race cam - 2nd opinion required
I've found best power at .88-.9 lambda on true e85 - 85% ethanol. I got it wrong, not standing mile it's rolling start 800m 1/2 mile. 238kmh so far in a xw falcon with the aerodynamics of a brick. I got a feeling you would make some more power if you were around .80-.84 lambda, but then again there...
- Thu Mar 02, 2017 11:41 am
- Forum: Engine Tech
- Topic: Cleveland road race cam - 2nd opinion required
- Replies: 73
- Views: 12372
Re: Cleveland road race cam - 2nd opinion required
Is this engine on gasoline or E85 with those AFR?
- Wed Dec 21, 2016 4:39 am
- Forum: Engine Tech
- Topic: The Next Generation of Lifter Technology......
- Replies: 52
- Views: 21333
Re: The Next Generation of Lifter Technology......
Any news on the Ford lifters?
- Sun Dec 11, 2016 4:42 pm
- Forum: Engine Tech
- Topic: The Next Generation of Lifter Technology......
- Replies: 52
- Views: 21333
Re: The Next Generation of Lifter Technology......
A Buddy of mine was at the PRI and asked when they are producing Ford Windsor lifters and they said to him in about 6-8 weeks,i just hope they get that oiling right when the lifter is on the base circle of the cam.
- Fri Dec 09, 2016 4:55 pm
- Forum: Engine Tech
- Topic: The Next Generation of Lifter Technology......
- Replies: 52
- Views: 21333
Re: The Next Generation of Lifter Technology......
When Morel make the new lifters for Ford Windsor are they going to have the oiling chamfer that comp have on their lifters or does the engine builder have to modify them? Have a look at the links below. http://www.ebay.com.au/itm/COMP-CAMS-ENDURE-X-SOLID-ROLLER-LIFTERS-FORD-SMALL-BLOCK-WINDSOR-CO-83...
- Mon Nov 28, 2016 9:08 pm
- Forum: Engine Tech
- Topic: Steel Distributor gear on Steel Roller Cam?
- Replies: 17
- Views: 5297
Re: Steel Distributor gear on Steel Roller Cam?
Gents this is the email i got back from CRANE CAMS! go figure !!! Our coated steel gears are only recommended for use with stock oil pumps. High pressure and high volume pumps will cause both gears to wear rapidly. Thanks, 866-388-5120 Ext. 4473 386-506-0321 (Direct) 386-236-9983 (Fax) http://www.cr...
- Mon Nov 28, 2016 4:58 am
- Forum: Engine Tech
- Topic: Steel Distributor gear on Steel Roller Cam?
- Replies: 17
- Views: 5297
Re: Steel Distributor gear on Steel Roller Cam?
http://www.yellowbullet.com/forum/showpost.php?p=8054674&postcount=18 Re: Crane coated steel distributor gear ive used the crane coated gears in our BBC endurance motors in boats, work fine, we also run a 2 piece cam shaft with a hardned gear on the cam Contact your mate in Sydney. Who is my ma...
- Mon Nov 28, 2016 4:56 am
- Forum: Engine Tech
- Topic: Steel Distributor gear on Steel Roller Cam?
- Replies: 17
- Views: 5297
Re: Steel Distributor gear on Steel Roller Cam?
This for a SBF Dart iron eagle block and planing on using a 9310 cam core.
- Mon Nov 28, 2016 1:28 am
- Forum: Engine Tech
- Topic: Steel Distributor gear on Steel Roller Cam?
- Replies: 17
- Views: 5297
Steel Distributor gear on Steel Roller Cam?
Hi Gents, Has anyone run one of these CRANE Steel distributor gears with a steel roller cam on a street driven engine with good results,or is there a better gear out there to run. just dont want to run a bronze gear with a internal oem style oil pump on the street they dont last. http://cranecams.co...
- Tue Nov 22, 2016 12:06 am
- Forum: Engine Tech
- Topic: New Morel Lifters
- Replies: 2
- Views: 1368
Re: New Morel Lifters
Nobody use these lifters
- Sat Nov 19, 2016 10:07 pm
- Forum: Engine Tech
- Topic: New Morel Lifters
- Replies: 2
- Views: 1368
New Morel Lifters
http://www.johncalliesinc.com/pdf/NPA_B ... 161026.pdf
Need a very good Solid roller lifter for SBF for 80% street and 20% road race use,4speed manual trans.Any feedback on these lifters?
Need a very good Solid roller lifter for SBF for 80% street and 20% road race use,4speed manual trans.Any feedback on these lifters?
- Thu Nov 19, 2015 4:36 am
- Forum: Engine Tech
- Topic: 18º 434 SBC Dyno Results
- Replies: 271
- Views: 48232
Re: 18º 434 SBC Dyno Results
Rick360, Have you done any calculations on convertor slip? Where does your rpm drop to on the shift and what rpm you cross at the finish line? The converter flashes to 6600 and falls back to 6500 until it climbs up in low. After the shift it is back to 6500. I only have a go-pro video of a pass to ...